Edge-Core ECS4610-26T Guia de Instalação descarregar pdf (Página 88)

HAPTER

| Link Layer Discovery Protocol

Configuring LLDP

– 88 –

◆ Port — Port identifier. (Range: 1-26)

◆ State — Enables LLDP message transmit and receive modes for LLDP

Protocol Data Units. (Options: Disabled, Tx/Rx, Rx only, Tx only;

Default: Disabled)

WEB INTERFACE

To configure global and port settings for LLDP:

1. Click Configuration, LLDP, LLDP Settings.

2. Enable LLDP for the switch.

3. If required, modified other LLDP parameters.

4. For one or a group of ports, set the LLDP mode.

5. Click Apply.

Figure 28: LLDP Settings

1 2 ... 83 84 85 86 87 88 89 90 91 92 93 ... 141 142

Management Guide 1
ECS4310-26T 1
Gigabit Smart Switch 1
ANAGEMENT 3
ABOUT THIS GUIDE 5
CONTENTS 7
SECTION III APPENDICES 125 10
– 11 – 11
– 12 – 12
– 13 – 13
– 14 – 14
GETTING STARTED 15
16
1 INTRODUCTION 17
18
System Defaults 21
Table 2: System Defaults 21
INITIAL SWITCH CONFIGURATION 23
Connecting to the Switch 24
Figure 1: Login Page 24
Figure 3: IP Settings Page 25
Figure 4: User Accounts Page 26
Changing a PC’s IP Address 27
WEB CONFIGURATION 29
30
3 USING THE WEB INTERFACE 31
32
Figure 5: Home Page 32
Table 4: Main Menu 33
4 SYSTEM SETTINGS 37
38
Displaying System Information 38
Figure 7: System Information 38
Setting a User Account 39
Figure 8: System Password 39
Setting an IP Address 40
5 PORT SETTINGS 45
46
6 LINK AGGREGATION 49
50
Creating Trunk Groups 50
CONFIGURING TRUNK SETTINGS 52
Configuring Trunk Settings 53
Configuring LACP 54
7 CREATING VLANS 57
58
Assigning Ports to VLANs 58
8 VLAN STACKING 61
62
VLAN Stacking Table 62
VLAN Stacking Settings 63
9 IGMP SNOOPING 65
66
Multicast Entry Table 66
IGMP Snooping Setting 67
10 SPANNING TREE 71
72
CONFIGURING STP PORT SETTINGS 75
Configuring STP Port Settings 76
Figure 23: STP Port Setting 78
11 QUALITY OF SERVICE 79
80
Port-Based Priority 80
DSCP-Based Priority 81
Priority-to-Queue Mapping 82
Table 9: CoS Priority Levels 83
Packet Scheduling 84
Figure 27: Packet Scheduling 85
LINK LAYER DISCOVERY PROTOCOL 87
Configuring LLDP 88
Figure 28: LLDP Settings 88
LLDP Neighbors 89
Figure 29: LLDP Neighbors 90
13 SNMP SETTINGS 91
92
Figure 30: SNMP Settings 93
14 PORT MIRRORING 95
96
Figure 32: Port Mirroring 96
15 PORT SECURITY 97
98
Figure 33: Port Security 98
16 BANDWIDTH CONTROL 99
100
Figure 34: Bandwidth Control 100
17 JUMBO FRAME 101
102
18 MANAGEMENT ACCESS FILTER 103
104
19 MAC ADDRESS SECURITY 105
106
Static MAC Addresses 106
MAC ADDRESS FILTERING 107
MAC Address Filtering 108
20 802.1X SECURITY 109
110
802.1X Global Settings 110
802.1X Port Settings 111
Figure 40: 802.1X Setting 111
WEB INTERFACE 112
21 GENERAL SECURITY SETTINGS 113
Storm Control Setting 114
Figure 42: IP Filter Setting 114
Port Isolation 116
Defence Engine 117
22 PORT STATISTICS 119
120
Figure 46: Port Statistics 120
23 MANAGEMENT TOOLS 121
122
Restoring Factory Defaults 122
Figure 47: Software Upgrade 122
Resetting the Switch 123
Figure 49: Reboot Switch 123
APPENDICES 125
126
A SOFTWARE SPECIFICATIONS 127
128
Management Features 128
Management Information Bases 129
B TROUBLESHOOTING 131
132
GLOSSARY 133
– 134 – 134
– 135 – 135
– 136 – 136
DIUS is a logon 137
– 138 – 138
– 139 – 139
– 140 – 140
E072010-CS-R01 142
149100000083A 142

Comentários a estes Manuais

Sem comentários

Edge-Core ECS4610-26T Guia de Instalação Página 88

Comentários a estes Manuais

Manuais e produtos relacionados com Comutadores de rede Edge-Core ECS4610-26T